Seminole Table Runner Finish

So I have finally finished quilting the Seminole Table Runner I showed in my last post. I am a little later posting than planned. Its been a rough couple weeks schedule wise around here but it is finally finished.

I really love quilting and trying new techniques together with tried and true methods. For me the tried and true method is FMQ with my BSR. New to me is walking foot quilting. I have used my walking foot in the past but I never quite got the results.

First things first I pin basted my layers together.

 To finish off this runner I used 100% cotton batting and a thermal fabric backing that way it can stay on the table during dinner and will take the place of trivets and pot holders. I grew up in a large family but we only have one stove top and sometimes a dual oven but to get the meal on the table and keep it hot we were rotating things in and out of the oven and always looking for pot holders to protect the table cloth and table. I used my dual feed foot (built in walking foot) to stitch in the ditch around the center patchwork. When doing stitch in the ditch I usually use my BSR, that way if my seams aren't quite straight or laying flat I can make the stitching fit at the ditch.

When I do use my walking/dual feed foot I do a finessing to make sure my stitch ends at the points. By using the hand wheel on my machine I can make the stitch a little longer or shorter to make it end where I need it.

Next I used my BSR to add detail quilting in the centre four patches. In the black square I added a triple petals and in the gray I did a side to side wave.  I moved across the centre of the quilt from end to end for the swirl and then added the triple petals after.

After the center four patch was done I put my 1/4 inch dual feed foot back on and stitched point to point  in the background fabric. I then also stitched a 1/4 inch on either side of the first stitch line.

When I got to the outside on the centre patch work I used my Hera Marker from Clover to mark the straight lines. I no longer had a point to shoot for with the stitching and adding the crease line from the Hera Marker made it easier to stay on the straight in relation to the rest of the lines.

Instead of cutting my thread when I reached and end point I back stitched/stitched in place to knot my thread and did a jump stitch. I usually do this when a jump stitch will waste less thread than cutting the thread and starting it again. If you use this method make sure you get a good knot in your thread otherwise you will lose your stitching and have to do it all over again. After I was done stitching I went back and clipped all the jump stitches.

After the middle of the runner was complete I used the dual feed foot and stitched in the ditch around the borders. Finally the runner was done, except for the binding, aka my least favorite part.

Thanks for stopping by!

Adrian

Table Runner

While my mom has been away in Alberta visiting my brothers, I have been busy working on store samples and getting ready for some late summer and fall classes. This post is for the Atkinson Designs Seminole Table Runner.

My first step was fabric selection...

Right now I really love using the Artisan Spirit Shimmer Collection from Northcott Fabrics. I chose a Black, Grey and Red palette.

I just love this whole line.  On to the pattern. I find patterns from this company really quite awesome. For this pattern the diagrams were great and the cutting instructions fantastic. My only complaints were the pressing instructions, some reverse sewing and the left over fabric (but who can't use extra fabric).

They have you start by making four patches. Sew the two strips together, Press to the background fabric. Sub-cut the strip set into smaller pieces then sew them back together. Voila! Four patch! 

When making multiple strip sets for a project I match the same ends together to help insure the same number of sub-cut pieces.  I make sure when piecing that I keep the fabric from peaking out from under my 1/4 inch foot and I use the markings on my stitch plate and the bed of the sewing machine to keep my sewing straight.

Then the pattern has you sew another strip set together. Which gets sub-cut and then added to either side of the four patch. When sewing long strips together even from the same collection the width of the fabric can vary. The directions at this point have you start pressing one strip set one way and one the other. By pressing in opposite directions you can't but the seams together for this step however. 

At this point in construction I pressed toward the red and in the four patch I kept the pressing to the background. I used the iron for the preliminary press but then finger pressed and pinned to get the seams to but against each other. 

For the next step you make another strip set of background and Red. Sew the strips together then sub-cut and add them to either side of all but two pieces, only add them to one of the sides on those two. Once this is done they want on two more the full pieces for you to remove the background from one side of the piece.

Leave the four odd men out until the last step and piece the rest together matching the two contrasting colours, in my table runner it is the black and dark grey. They will form the centre of this runner

.

When the full pieces are together you can now add the odd men out. 

Its a little weird you need to continue the off setting of the pieces and then we will trim them down.

We now add two strips to each side of the ends, add some more background grey to the centre of the runner. The directions say to lay it as flat as possible, lay the strip next to the spot on the runner and sew it together, trim off the excess. I really hate doing it that way so I measure the side and cut the strip to fit. I did this for both sides and both ends of the runner.

Next you trim off the jagged sides. Pay close attention to this because we are now making this a biased edge runner.

We now get to add the narrow inner border, I chose the black!

Next up trimming of the ends to make the angle and adding then end pieces. This is done for the inner narrow border and the outer border ( I missed taking photos of that step in black but I have it in red!)

Again when adding these pieces the directions show sewing them on without measuring and cutting them to length after. I didn't do this I measured, sewed and trimmed off to make the angles.

The runner is now complete!

This is me pinning it to the 100% cotton batting and Thermal Fabric backing! Come back next week to see the quilted finish!

Thanks for stopping by!

Adrian